Hi DIY!
My headphones of many years recently broke. My first response was to attempt to glue them back together with super glue (ethyl 2-cyanoacrylate) however that didn’t seem to hold. Not even a little bit.
I then did a bit of searching and found that Sony often use ABS plastic in headphone manufacture, so presumably these are ABS. I then read super glue should work okay on ABS, however there seemed to be no bonding happening at all.
Do any of you have any tips for the best kind of glue or epoxy to bond these plastic parts back together and get the music flowing again?
I plan on wrapping the joints in thread afterwards, for additional durability. But first I need to get them bonded.
Glues are fucking useless unless you have a large surface area to bond. Headphones don’t use ABS, too brittle. The use polycarbonate on the hoop that breaks and that doesn’t bond well with glue.
Hot staples are an option because the embed steel wire into the plastic. These kits are cheap now and very common in automotive plastic repair because glue is universally useless.
Gloop gets used in 3d printing. It physically welds the bonds together on a molecular level between 2 plastics.
Gloop is just acetone and tetrahydrofuran. That shit is toxic AF.
Superglue sprinkled with baking soda creates incredibly strong bonds. But you’ll need to add it all around the seam to make a thick layer.
I also recommend first scratching the plastic with sandpaper so that there’s something for the glue to hold on to.
I bought a cheap Temu plastic repair welder (melts in a little metall pin) - they actually work and the results are surprisingly strong.
I would make some metal rods to insert in the holes left in the hollow plastic. Epoxy those in place on both sides to reinforce the joints which will have stress on them. I think that is the only chance you have of repairing broken plastic like this with little surface area to bond. You could look around and find some nails or something to cut up.
@punksnotdead@slrpnk.net I would suggest carbon fiber rods or aluminum, ferris metal could interfere with the bluetooth radio depending on their shape.
I seriously doubt that.
This is just called plastic welding and it’s fantastic
Great idea! I’ll give that a go, thanks. Reinforcement rods, adhesive, and thread wrap around the outside should surely be enough
Might be able to find some wire in an electrical or automotive store. 20 guage is about a millimeter or less, 12 guage is between 2 and 3 mm. Do you have calipers to take a measurement?
Wire Coat Hanger might fit, will be harder so a better reinforcement.
General purpose tip for Gluing:
Isopropyl Alchohol in a spray mister will speed up Superglue bond time from minutes to seconds.
Mixing glues can be very useful. For example, I’ll use Epoxy for the hollow insides but a drop of Superglue where pieces fit together to hold the pieces together while the Epoxy cures overnight. UV glue is fantastic for that because it cures instantly. But a drop of Superglue with a spritz of alcohol works good too.
Cyanoacrylate accelerator is not IPA. It’s a mix of acetone and amines. You are getting a weak effect from the water in the IPA.
If the adhesive route fails, it looks like there are replacement parts available, but your mileage may vary when it comes to the source. Not seeing anything official, but ebay has a few hits: https://www.ebay.com/itm/204942975498
Might also try just calling Sony support, but iirc their support is fairly shit.
Ouch, I used hot glue for mine but its not great at holding to the surface, I just had a massive surface to make use of and pretty much made a ring of glue around the break. Doesn’t look like yours would work with that sadly.
So, probably don’t go with hot glue.
Maybe try JB-Weld? Idk if super glue will hold up here.
Great for:
- PVC
- ABS
- Rigid plastics
https://www.jbweld.co.uk/copy-of-marineweldsyr-25ml
This may be a winner, thanks!
It won’t work unless there is a large surface area.
Jb weld was going to be my suggestion too. Good luck OP
Came here to say this. JB-Weld is really great stuff. I’ve fixed a lot of things with it.
There is a jb-weild specific for plastic that works well
Glue guide!
Bookmarked! Thank you
physical reinforcement is a good suggestion lots are coming up with. If it’s not too late, I’d recommend doing that with something that dissolves the ABS instead of an adhesive. ABS dissolves readily with a few solvents, like acetone. Get physical reinforcement in place, and IF you do not need any bulk filler, just use a solvent like acetone to literally melt and repolymerize the plastic back together. As long as there’s no new gaps or new voids, the physical reinforcement should leave it stronger than the original. At least after all the solvent evaporates away.
If you need gap filler or bulk reinforcement, two part epoxies are definitely the way to go, though make sure to use something quite flexible or it’ll just crack off the next time you drop them.
Speaking of physical reinforcement, when my headphones broke in a very similar way I was able to use cable ties to secure them back together. Ugly but it worked.
I’ll be honest, you’re probably not going to be able to fix those to a degree that I’d trust. Some headphones are reparable and have replaceable parts, and that isn’t one of them. I’ve had really good luck with Audio-Technica and Beyer Dynamic in that department, but most of their more sturdy and repairable headphones aren’t very portable.
If it’s ABS (which most thugs are) try methyl ethyl ketone to melt it back together.
Just a dab of MEK will melt the plastic, but it evaporates/dissolves quickly. Once you apply it press the pies together firmly for a few minutes, then let it cure for a while after that. The bond should be as strong as it was from the factor. Then if you want apply some JB weld for extra strength.
Let’s not suggest a neurotoxin.
UV Glue will fix that no problems, and the glue will be stronger than the underlying plastic.
I have never seen this to be true.
The problem with uv glue is it needs light to cure. So it can’t be used to fill that broken area or inside the break itself. It can only coat the outside.
Not with that attitude (unscrews the entire thing and shoves in a UV light on a wire in the gaps)
Next time I find myself with the right assortment of junk, it would be interesting to run a piece of optical fiber through UV glue inside an opaque enclosure and see if it helps the light get where it needs to go. There’s decorative stuff that glows from the sides with a visible light source so I’d expect it to do something worthwhile in that situation. Could be a waste of materials for almost every possible use but maybe it’ll solve a weird problem eventually.
I didn’t even know there was such a thing. Buying a UV lamp for a single repair when other options are available feels a bit antithetical to the Solarpunk ethos though, so I think I’ll try normal glues first. But hey, if all else fails, at least I know there’s a nuclear option as plan b. Thanks!
There is a JB Weld UV glue product that comes with a UV LED attached:
https://www.jbweld.com/product/superweld-light-activated
It’s a blend, not pure UV resin, that will harden quickly where the light hits it but will also slowly cure without UV exposure, so the inner parts of the joint will harden over time.
I use this and I’ve found that it is almost as good as standard 2-part epoxy in most cases, and easier to use.
You can also cure UV glue in sunlight. It’s a bit of a pain and can take longer, but it’s an option.
Solar
punkglue. Hmm…
If you’re trying to be true to the “solarpunk ethos,” do you really think this is the last repair you’ll ever do?
I, for one, have never regretted letting a ‘one time’ project be an excuse to get a new type of tool.
(Just don’t get the disposable UV light another reply mentioned; that really is a bit wasteful. If you decide to go the UV glue route, get an inexpensive but proper standalone UV flashlight.)
Depends on the tool and its cost for me. If its something I can realistically see using again and is a reasonable price then sure.
That looks like toast.
3D printed replacement parts might work. If you have a maker space around you, you might be able to find someone to help you with the drafting/CAD.
